tag:blogger.com,1999:blog-1024848558336119865.post3365206308869216100..comments2024-03-20T02:26:18.297-04:00Comments on Sublime Layers: RepRapFirmware dc42 branch config filesSublimeLayershttp://www.blogger.com/profile/07266175443539080935noreply@blogger.comBlogger6125tag:blogger.com,1999:blog-1024848558336119865.post-19947039193927952392016-04-27T14:07:06.536-04:002016-04-27T14:07:06.536-04:00did you ever achieve a good multi color print with...did you ever achieve a good multi color print with the kraken?<br />i just try to figure out how to set the nozzle offsets etcAnonymoushttps://www.blogger.com/profile/13255136791129503477noreply@blogger.comtag:blogger.com,1999:blog-1024848558336119865.post-83112972367590502572016-04-26T08:11:09.334-04:002016-04-26T08:11:09.334-04:00Thank you Gerhard. Good luck with your thesis!Thank you Gerhard. Good luck with your thesis!SublimeLayershttps://www.blogger.com/profile/07266175443539080935noreply@blogger.comtag:blogger.com,1999:blog-1024848558336119865.post-50573284226059608862016-04-26T02:35:22.376-04:002016-04-26T02:35:22.376-04:00thank you
i am really sorry for questions that are...thank you<br />i am really sorry for questions that are allready answered somewhere.<br />there are so much informations around the net... XD it is really hard to sort out the correct ones. i think you are a big help for many home makers with your patient answers :-).<br />Im writing my bachelor-thesis right now about a food printer im developing right now, and some of your stuff will be definetly part of it (of course with sources ;-))Anonymoushttps://www.blogger.com/profile/13255136791129503477noreply@blogger.comtag:blogger.com,1999:blog-1024848558336119865.post-63948695328607364672016-04-20T14:49:39.548-04:002016-04-20T14:49:39.548-04:00Gerhard, David Crocker has some information of the...Gerhard, David Crocker has some information of the process on his web site here: https://miscsolutions.wordpress.com/2015/01/05/upgrading-the-mini-kossel-to-duet-electronics-part-2-software-and-commissioning/<br /><br />However, a better more accurate method that he alluded to is to use two high precision resistors (one for the high temp calibration and one for the low temp calibration). You can read about it here: http://forums.reprap.org/read.php?340,326029<br /><br />I bought a pack of each resistor from an eBay vendor. You need:<br /><br />one 100k 1% resistor<br />one 220ohm 1% resistor <br /><br />This method works great and if you have more than 1 printer, they will all be dead-on calibrated with each other.SublimeLayershttps://www.blogger.com/profile/07266175443539080935noreply@blogger.comtag:blogger.com,1999:blog-1024848558336119865.post-51005736665129046842016-04-20T13:58:57.411-04:002016-04-20T13:58:57.411-04:00how did you calibrate your M305? i can heat up my ...how did you calibrate your M305? i can heat up my hotend to 230° and in real it is like 180°...<br />Anonymoushttps://www.blogger.com/profile/13255136791129503477noreply@blogger.comtag:blogger.com,1999:blog-1024848558336119865.post-67338679209080809422016-01-06T11:36:07.239-05:002016-01-06T11:36:07.239-05:00Thanks for posting this.Thanks for posting this.Anonymoushttps://www.blogger.com/profile/01660856701470212767noreply@blogger.com